Poulan 14 Inch Electric Chainsaw Manual

The Poulan 14 Inch Electric Chainsaw is a lightweight, easy-to-use chainsaw designed for residential yard work, featuring a 14-inch Oregon bar and chain, 120V AC electric motor, automatic oiler, tool-free chain tensioning, low-kickback design, and safety features including a chain brake and hand guard. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Safety Information 3. Assembly & Setup 4. Specifications 5. Controls and Components 6. Operation Instructions 7. Chain Maintenance 8. Cleaning & Storage 9. Troubleshooting 10. Warranty Information

Features at a Glance

Key components: Electric motor, 14-inch Oregon bar and chain, automatic oiler, front hand guard, chain brake, tool-free chain tensioning system.

Feature	Description
14-inch Oregon bar	For cutting logs up to 14 inches in diameter
Automatic oiler	Lubricates chain during operation
Tool-free chain tensioning	Adjust chain tension without tools
Chain brake	Stops chain immediately upon kickback
Front hand guard	Protects hands from debris
Low-kickback design	Reduces risk of kickback incidents
Lightweight body	Easy to handle and maneuver
Electric motor	120V AC, no gas or oil mixing required
Safety trigger lock	Prevents accidental starting
Oiler adjustment dial	Controls oil flow rate

Safety Information

Read all instructions before use. Always wear safety gear.

Wear safety glasses, gloves, ear protection, and sturdy footwear.
Keep bystanders and pets at least 15 feet away.
Inspect chainsaw before each use for damage or loose parts.
Ensure chain is properly tensioned and sharp.
Use both hands on handles during operation.

WARNING! Risk of electric shock. Do not use in wet conditions. Keep cord away from cutting area.

Assembly & Setup

Unpack and inspect all parts. Assemble on a flat, stable surface.

Attach bar and chain: Place bar onto mounting studs, loop chain around bar with cutting teeth facing forward, adjust tension.
Install chain brake: Ensure brake is in off position (forward).
Fill oil reservoir: Use bar and chain oil only; fill to MAX line.
Plug into grounded 120V outlet; test safety features.

CAUTION! Ensure chain is properly installed to prevent derailment. Do not force parts.

Specifications

Bar Length: 14 inches.
Motor: 120V AC, 60Hz, 12 Amp.
Chain Pitch: 3/8 inch low-profile.
Chain Gauge: 0.050 inch.
Oil Capacity: 4.0 oz.
Weight: 7.5 lbs (without cord).
Cord Length: 6 feet (use extension cord if needed, 14 AWG minimum).
Sound Level: < 90 dB.
Recommended Use: Pruning, limbing, cutting firewood.

Controls and Components

Main components: Front handle with safety trigger, rear handle with throttle trigger, chain brake lever, oiler dial, tensioning knob.

Controls: Safety trigger lock (must be depressed before throttle), throttle trigger (right handle), chain brake (front guard), oiler adjustment dial (side), tensioning knob (side).

Operation: Depress safety lock, then squeeze throttle to start chain. Release throttle to stop chain. Engage chain brake by pushing guard forward. Adjust oil flow with dial (MIN to MAX).

Operation Instructions

For cutting logs, branches, and pruning.

Check oil level and chain tension before each use.
Clear work area of obstacles and debris.
Hold chainsaw firmly with both hands, feet shoulder-width apart.
Start cut at full throttle; let chain do the work—do not force.
For bucking: Support log off ground; cut from top down.
For limbing: Cut branches from bottom of tree upward.
After cutting, release throttle and engage chain brake.

Tip: Avoid cutting with tip of bar to prevent kickback. Keep cord behind saw.

Chain Maintenance

Regular maintenance ensures optimal performance and safety.

Sharpening: Use round file (5/32 inch) every few hours of use; maintain 30-degree angle.
Tensioning: Chain should snap back when pulled from bar; adjust with tensioning knob.
Lubrication: Check oil level frequently; refill with bar and chain oil.
Inspection: Look for worn drive links, damaged cutters, and bar groove wear.
Replacement: Replace chain when cutters are worn beyond repair or stretched.

WARNING! Always unplug chainsaw before performing maintenance. Wear gloves.

Cleaning & Storage

Unplug and cool before cleaning. Wipe exterior with dry cloth; remove sawdust from air vents and bar.

Storage: Empty oil reservoir or store upright. Keep in dry, locked area away from children. Cover bar with guard.

CAUTION! Do not use water or solvents; avoid storing in damp locations.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Chain does not move	Safety lock engaged; low power	Depress safety lock; check outlet and cord; reset breaker.
Chain slips or derails	Loose tension; worn bar	Tighten chain; inspect bar groove; replace if worn.
Excessive vibration	Loose parts; dull chain	Tighten all fasteners; sharpen chain.
Chain does not oil	Empty reservoir; clogged port	Refill oil; clean oil ports with needle.
Motor hums but no rotation	Jammed chain; faulty motor	Clear jam; unplug and inspect; contact service.

Reset: Unplug for 30 seconds if motor overheats.

Service: 1-800-554-6723; www.poulan.com

Warranty Information

2-year limited warranty from date of purchase. Covers defects in materials and workmanship. Does not cover normal wear, misuse, or unauthorized repairs. Proof of purchase required. For warranty claims, contact Poulan customer service or authorized service center.