Husqvarna 316 Electric Chainsaw Manual

The Husqvarna 316 is a lightweight, electric chainsaw designed for domestic use, featuring a 40 cm (16") guide bar, chain brake, low noise operation, and an automatic chain lubrication system. It is powered by a 230V electric motor, making it ideal for pruning, cutting firewood, and general garden maintenance. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Safety Instructions 3. Assembly & Installation 4. Specifications 5. Controls and Components 6. Operation Guide 7. Chain Maintenance 8. Cleaning & Storage 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Electric motor, 40 cm (16") guide bar, chain brake, front hand guard, automatic oiler, tensioning system, and ergonomic rear handle with safety trigger.

Feature	Description
Guide Bar Length	40 cm (16 inches)
Power Source	230V Electric Motor
Chain Brake	Inertia-activated safety feature
Automatic Oiler	Lubricates chain during operation
Noise Level	Low noise design for residential use
Weight	Lightweight for easy handling
Safety Trigger	Prevents accidental start
Tensioning System	Tool-free chain adjustment
Hand Guard	Protects front hand from debris
Carrying Case	Included for storage and transport

Safety Instructions

Read all instructions before use. Always wear protective gear.

Personal Protective Equipment: Wear safety glasses, gloves, ear protection, and sturdy footwear.
Work Area Safety: Ensure clear area, secure footing, and no bystanders.
Electrical Safety: Use proper extension cord; keep cord away from cutting area.
Operation: Hold with both hands; never operate above shoulder height.

WARNING! Risk of electric shock and kickback. Never use in wet conditions. Always engage chain brake when not cutting.

Assembly & Installation

Unpack and inspect contents. Assemble guide bar and chain.

Attach Guide Bar: Place bar on mounting studs, align chain sprocket.
Install Chain: Fit chain around bar, ensuring cutting teeth face forward.
Tension Chain: Adjust tensioning screw until chain snaps back when pulled.
Fill Oil Tank: Use Husqvarna chain oil; fill to marked level.
Connect Power: Plug into 230V outlet; ensure cord is undamaged.

CAUTION! Ensure chain is properly tensioned. Loose chain may derail or break.

Specifications

Model: Husqvarna 316
Power: 2000W Electric Motor
Guide Bar: 40 cm (16 inches)
Chain Pitch: 3/8"
Chain Gauge: 1.3 mm
Oil Tank Capacity: 200 ml
Weight: 4.2 kg (without cord)
Voltage: 230V, 50Hz
Sound Pressure: 94 dB(A)
Vibration: Front handle 3.5 m/s², Rear handle 2.5 m/s²

Controls and Components

Main components: Front handle with hand guard, rear handle with safety trigger, chain brake, guide bar, chain, oil filler cap, tensioning screw.

Controls: ON/OFF switch, safety trigger (must be pressed to activate switch), chain brake lever (forward to engage, backward to disengage).

Operation: Press safety trigger, then ON switch. Release trigger to stop chain. Engage chain brake for safety stops. Adjust chain tension via side screw. Check oil level via sight window.

Operation Guide

Starting and basic cutting techniques.

Pre-Start Check: Ensure chain tension, oil level, and clear work area.
Starting: Press safety trigger, then ON switch. Allow chain to reach full speed.
Cutting: Apply light pressure; let chain do the work. Avoid twisting or forcing.
Kickback Prevention: Hold firmly, avoid tip contact, use reduced kickback chain.
Stopping: Release trigger; engage chain brake when moving between cuts.

Tip: For pruning, cut from top down. For felling, plan escape path and notch properly.

Chain Maintenance

Regular maintenance ensures optimal performance and safety.

Sharpening: Use round file (4.5 mm) every 2-3 hours of use. Maintain 30° angle.
Tensioning: Check frequently; chain should snap back when pulled from bar.
Lubrication: Refill oil tank before each use. Use only Husqvarna chain oil.
Bar Maintenance: Clean bar groove; rotate bar regularly for even wear.
Chain Replacement: Replace when drive links are worn or cutting inefficient.

WARNING! Always disconnect power before maintenance. Wear gloves when handling chain.

Cleaning & Storage

Unplug and clean after each use. Store in dry, secure location.

Cleaning: Wipe exterior with dry cloth; clean air vents; remove sawdust from bar and chain.
Storage: Empty oil tank or use stabilizer; store in carrying case away from moisture.
Long-Term: Remove chain, clean and oil it; cover saw to prevent dust accumulation.

CAUTION! Do not use water or solvents. Store out of reach of children.

Regulatory Information

CE certified. Complies with EU machinery directive 2006/42/EC and EMC directive 2014/30/EU. Contains electrical components that must be recycled separately. For EU disposal, follow WEEE guidelines. Husqvarna is a registered trademark. For support, visit www.husqvarna.com or contact your local dealer.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Chainsaw won't start	Power supply, safety trigger	Check outlet, extension cord; ensure safety trigger is pressed.
Chain doesn't move	Chain brake engaged, loose chain	Disengage chain brake; adjust chain tension.
Poor cutting performance	Dull chain, low oil	Sharpen chain; refill oil tank.
Chain throws oil	Overfilled oil tank	Drain excess oil to correct level.
Excessive vibration	Loose components, worn chain	Tighten bar nuts; check chain for damage.
Motor overheats	Blocked air vents, dull chain	Clean vents; sharpen chain; allow to cool.

Service: For electrical or motor issues, contact authorized Husqvarna service center.

Support: 1-800-HUSKY-11; www.husqvarna.com