Homelite XL Chainsaw UT 10695 Manual

The Homelite XL Chainsaw UT 10695 is a professional-grade chainsaw designed for demanding cutting tasks. It features a powerful 2-stroke engine, automatic oiling system, anti-vibration handles, chain brake, and a durable 16-inch guide bar. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: 2-stroke gasoline engine, 16-inch guide bar, automatic chain oiler, anti-vibration system, chain brake, throttle lockout, and decompression valve.

Safety Information

Read all instructions before use. Wear proper safety gear.

1. Always wear: Safety glasses, hearing protection, gloves, chainsaw chaps, and steel-toed boots.
2. Clear work area of obstacles and bystanders.
3. Check chain tension and sharpness before each use.
4. Never operate with damaged or missing parts.

WARNING! Risk of severe injury or death from kickback, chain contact, or falling branches. Maintain firm grip with both hands.

Assembly Instructions

Unpack and inspect contents. Assemble on a clean, flat surface.

1. Attach guide bar: Loosen bar nuts, position bar over studs, align chain drive links with sprocket.
2. Install chain: Place chain over bar, ensuring cutting teeth face forward on top.
3. Tension chain: Adjust tensioning screw until chain snaps back when pulled from bar.
4. Tighten bar nuts: Secure while lifting bar tip upward.
5. Fill oil reservoir: Use bar and chain oil only.
6. Mix fuel: 50:1 gasoline to 2-stroke oil ratio (recommended).

CAUTION! Ensure chain is properly tensioned—too loose may derail; too tight may damage bar.

Specifications

• Model: Homelite XL UT 10695
• Engine: 45.7 cc 2-stroke
• Power Output: 2.5 kW (3.4 hp)
• Fuel: Unleaded gasoline (min 89 octane) with 2-stroke oil
• Fuel Mix Ratio: 50:1
• Bar Length: 16 inches (40 cm)
• Chain Speed: 18.5 m/s at max RPM
• Weight (dry): 5.2 kg (11.5 lbs)
• Sound Pressure Level: 108 dB(A)
• Vibration Level: 4.2 m/s² (front/rear handles)

Controls and Components

Main components: Front handle with throttle trigger, rear handle with throttle lockout, choke lever, ignition switch, decompression valve, chain brake lever, and oil filler cap.

Controls: Throttle trigger (accelerates engine), Throttle lockout (must be depressed to engage throttle), Choke (for cold starts), Ignition switch (ON/OFF), Chain brake (manual/automatic activation), Decompression valve (reduces cylinder pressure for easier starting).

Maintenance points: Air filter cover, spark plug, chain tensioning screw, bar nuts, oil reservoir cap.

Starting & Operating

Starting procedure (cold engine):

1. Place chainsaw on flat ground, clear of debris.
2. Engage chain brake by pushing lever forward.
3. Set ignition switch to ON.
4. Pull choke lever to FULL position.
5. Press decompression valve (if equipped).
6. Hold front handle with left hand, place right foot in rear handle.
7. Pull starter rope briskly until engine fires.
8. Push choke to HALF position, pull starter again until engine runs.
9. Disengage chain brake before cutting.

Tip: Warm up engine at idle for 30 seconds before applying load.

Chain & Bar Maintenance

Regular maintenance ensures optimal performance and safety.

1. Chain sharpening: Use round file (5/32 inch) at 30° angle. File each cutter evenly.
2. Chain tension: Check frequently; adjust when chain sags from bar.
3. Bar maintenance: Clean bar grooves, flip bar monthly for even wear.
4. Oiler check: Ensure oil flow by holding saw over light surface and running at high idle—oil should appear on chain.
5. Replace chain: When cutters are worn below 4 mm or damaged.

WARNING! Always wear heavy gloves when handling chain. Ensure ignition is OFF.

Engine Maintenance

Follow regular service intervals for engine longevity.

CAUTION! Use only recommended 2-stroke oil. Never use automotive oil.

Storage Guidelines

Prepare chainsaw for extended storage to prevent fuel system damage.

1. Drain fuel tank and run engine until it stops.
2. Remove spark plug, add 1 teaspoon of oil into cylinder, pull starter slowly to distribute.
3. Clean entire saw, especially air intake and cooling fins.
4. Loosen chain tension to relieve pressure on bar.
5. Store in dry, cool place, away from children.

CAUTION! Never store with fuel in tank for more than 30 days. Fuel may degrade and damage carburetor.

Warranty Information

Homelite XL UT 10695 comes with a 2-year limited warranty for residential use and 1-year for commercial use. Warranty covers defects in materials and workmanship. Not covered: normal wear, misuse, improper maintenance, or use of non-genuine parts. For warranty claims, contact authorized service center with proof of purchase. For support, visit www.homelite.com or call 1-800-242-4672.

Troubleshooting

Service: For repairs, contact authorized Homelite service center. Do not attempt major engine repairs without proper training.

Support: 1-800-242-4672; www.homelite.com