Homelite Textron Chainsaw Manual - 10655

The Homelite Textron Chainsaw Model 10655 is a gasoline-powered chainsaw designed for general-purpose cutting, pruning, and limbing. It features a 2-stroke engine, automatic oiling system, anti-vibration handles, chain brake, and a guide bar of varying lengths (commonly 14-18 inches). Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Fuel & Lubrication 7. Operating Procedures 8. Maintenance Schedule 9. Storage & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 2-stroke gasoline engine, Guide Bar, Chain, Chain Brake, Throttle Trigger, Choke Control, Fuel Tank, Oil Tank, Anti-Vibration Handles, Spark Plug, Air Filter.

Feature	Description
Engine Type	2-stroke, air-cooled gasoline engine
Guide Bar	14-18 inch bar length (model dependent)
Chain Brake	Inertia-activated safety brake to stop chain
Automatic Oiling	Pumps bar & chain oil during operation
Anti-Vibration	Reduces operator fatigue
Throttle Trigger	Controls engine speed; includes safety lock
Choke Control	Assists in cold starting
Fuel Tank	Capacity approximately 0.5-0.7 liters
Oil Tank	For chain lubrication, separate from fuel
Spark Plug	Standard reach, replaceable

Assembly & Installation

Unpack and inspect contents. Assemble on a clean, flat surface.

Attach Guide Bar & Chain: Loosen bar nuts, position bar, loop chain over sprocket, tension correctly.
Install Handle: Secure front and rear handles with provided bolts.
Fill Fluids: Add fuel mix (gasoline & 2-stroke oil) to fuel tank; add bar & chain oil to oil tank.
Check Chain Brake: Ensure brake mechanism moves freely and engages properly.

WARNING! Always wear protective gloves during assembly. Ensure chain is properly tensioned before use.

First-Time Setup

Before first start, complete pre-operation checks.

Fuel Mix: Use fresh unleaded gasoline mixed with 2-stroke oil at ratio specified in manual (e.g., 50:1).
Chain Tension: Adjust so chain snaps back when pulled from bar; not too tight.
Check Controls: Verify throttle trigger, choke, and chain brake function smoothly.
Start Engine: Place on ground, engage chain brake, set choke, pull starter cord.

CAUTION! Operate only in well-ventilated areas. Keep bystanders away.

Specifications

Model: Homelite Textron 10655
Engine Displacement: Typically 40-50cc (check specific model)
Fuel: Gasoline with 2-stroke oil mix
Bar Length: 14", 16", or 18" options
Chain Pitch/Gauge: .325" pitch, .050" gauge (common)
Weight: Approximately 10-12 lbs (without fuel)
Ignition: Electronic
Sound Level: Exceeds 100 dB; hearing protection required
Vibration: Reduced via anti-vibration system

Controls and Settings

Main Controls: Throttle Trigger (with lockout), Choke Lever, Stop Switch, Chain Brake Handle, Primer Bulb (if equipped).

Adjustments: Chain Tension (via side knob), Idle Speed (carburetor screw), Oil Flow Rate (adjustment screw on oil pump).

Operation: Start with choke, then run position. Use throttle to control cutting speed. Engage chain brake when not cutting or for emergency stop.

Fuel & Lubrication

Fuel: Mix fresh unleaded gasoline (87 octane minimum) with 2-stroke engine oil at specified ratio (e.g., 50:1). Shake well before filling.

Fuel Tank: Fill to marked level; avoid overfilling.
Chain Oil: Use dedicated bar & chain oil; fill separate oil tank.
Check Oil Flow: Run saw at high idle; look for oil sling on ground or bar tip.

Tip: Never use straight gasoline or motor oil. Do not mix fuels more than 30 days old.

Operating Procedures

Supports cutting of logs, pruning, limbing.

Starting: Set chain brake, move choke to START, pull starter cord until engine fires, then move choke to RUN, pull again.
Cutting: Release chain brake, apply light pressure, let chain do the work.
Kickback Prevention: Hold firmly, avoid tip contact, cut at full throttle.
Stopping: Release throttle, engage chain brake, press STOP switch.
Refueling: Stop engine, allow to cool, clean area, refill tanks.

WARNING! Always wear PPE: eye protection, hearing protection, gloves, chainsaw chaps, steel-toe boots. Beware of kickback.

Maintenance Schedule

Daily: Check chain tension, sharpness, fluid levels. Clean air filter, check for loose parts.

Weekly: Inspect spark plug, clean cooling fins, check bar for wear, lubricate sprocket tip.

Monthly: Clean fuel filter, replace spark plug if needed, inspect anti-vibration mounts.

Seasonal: Drain fuel for storage, clean entire saw, sharpen or replace chain, check clutch.

Storage & Cleaning

Drain fuel tank and run carburetor dry. Remove chain, clean with solvent, oil lightly. Store in dry place, covered.

CAUTION! Never store with fuel in tank for more than 30 days. Keep away from open flames.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
Engine won't start	No fuel, flooded, bad spark	Check fuel, wait if flooded, check spark plug, clean air filter.
Engine runs then dies	Clogged fuel filter, carburetor	Replace fuel filter, clean carburetor, check fuel lines.
Chain doesn't turn	Brake engaged, clutch worn	Disengage brake, inspect clutch drum/sprocket.
Chain throws oil	Oil flow too high	Adjust oil pump screw to reduce flow.
Excessive vibration	Loose parts, unbalanced chain	Tighten all bolts, balance chain, check anti-vibration mounts.

Reset: For electronic ignition, disconnect spark plug wire, pull starter 5 times to clear flood.

Service: 1-800-242-4672; www.homelite.com