Craftsman Pro Series Chainsaw Manual

The Craftsman Pro Series Chainsaw is a professional-grade power tool designed for demanding cutting tasks. It features a high-performance gas engine, automatic oiling system, low-kickback bar and chain, tool-less chain tensioning, anti-vibration handles, and a quick-stop chain brake for enhanced safety. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: High-torque 2-stroke engine, 18-inch guide bar, automatic chain oiler, inertia-activated chain brake, anti-vibration system, and easy-start technology.

Safety Information

Read and understand all instructions before operating. Always wear appropriate personal protective equipment (PPE).

1. PPE Required: Safety glasses, hearing protection, gloves, chainsaw chaps, and sturdy boots.
2. Work Area Safety: Clear area of bystanders, especially children and pets. Ensure secure footing.
3. Kickback Warning: Keep firm grip, do not cut with tip of bar. Use reduced-kickback chain and low-kickback bar.
4. Fuel Safety: Refuel in well-ventilated area, away from ignition sources. Allow engine to cool.

WARNING! Improper use can cause serious injury or death. Always engage chain brake when not cutting.

Assembly & Setup

Unpack and inspect all parts. Assemble on a clean, flat surface.

1. Attach Guide Bar & Chain: Place bar on mounting studs. Loop chain over sprocket and onto bar groove. Adjust tension.
2. Install Handle: Secure front and rear handles with provided bolts.
3. Fill Fluids: Mix gasoline with 2-stroke oil at 50:1 ratio. Fill fuel tank. Fill oil tank with bar and chain oil.
4. Check Chain Tension: Chain should snap back when pulled from bar. Adjust using tool-less tensioner.

CAUTION! Ensure chain is installed with cutting teeth facing forward on top of bar.

Specifications

• Engine: 50cc 2-stroke, air-cooled.
• Power Output: 3.2 HP at 9,500 RPM.
• Fuel: Unleaded gasoline (87 octane min.) with 2-stroke oil (50:1 mix).
• Bar Length: 18 inches.
• Chain Speed: Max 65 ft/sec (19.8 m/sec).
• Weight (dry): 12.8 lbs (5.8 kg).
• Sound Pressure Level: 105 dB(A).
• Vibration Level: Front handle 4.2 m/s², rear handle 3.8 m/s².
• Warranty: 2-year limited warranty.

Controls and Components

Main Controls: Throttle trigger, throttle trigger lockout, stop switch, choke control, primer bulb, chain brake lever.

Components: Front handle with chain brake, rear handle with throttle, fuel tank cap, oil tank cap, air filter cover, spark plug, muffler, guide bar, chain, and sprocket cover.

Operation: Pull choke for cold start. Press primer bulb 5-6 times. Set stop switch to "I". Pull starter rope. Disengage choke as engine warms. Squeeze throttle trigger lockout and throttle to accelerate. Engage chain brake by pushing lever forward.

Fuel & Oil

Use fresh unleaded gasoline (87 octane minimum) mixed with high-quality 2-stroke engine oil at 50:1 ratio.

1. Mix fuel in approved container: Add oil to gasoline, shake thoroughly.
2. Fill fuel tank to 80% capacity to allow for expansion.
3. Use standard bar and chain oil in oil tank. Do not use waste oil.
4. Check oil flow: Hold saw over light surface and run at high speed; look for oil sling.

Tip: Always use fuel stabilizer if storing for more than 30 days.

Operation

Supports felling, limbing, bucking, and pruning.

1. Starting: Engage chain brake. Set choke, prime, pull starter until engine fires. Disengage choke, restart.
2. Cutting: Hold saw firmly. Let chain reach full speed before contacting wood. Use lower part of bar for cutting.
3. Kickback Prevention: Never cut with upper tip. Maintain secure grip. Keep saw at waist level or below.
4. Stopping: Release throttle, allow engine to idle. Engage chain brake. Press stop switch to "0".
5. Refueling: Stop engine and allow to cool. Clean area around fuel cap. Refill carefully.

WARNING! Do not operate with loose or damaged chain. Always shut off engine when transporting.

Maintenance

Daily: Check chain tension, sharpness, and lubrication. Clean air filter. Inspect for loose parts.

Weekly: Clean spark arrestor screen. Check fuel filter. Clean cooling fins.

Monthly: Replace spark plug. Clean carburetor air filter. Inspect bar for wear, flip bar regularly.

Chain Sharpening: Use round file and guide. Maintain 30° cutting angle. File all cutters evenly.

Storage

Long-term storage: Drain fuel tank and run engine until it stops. Remove spark plug, add 1 tsp oil, pull starter slowly. Clean entire saw. Store in dry, locked area.

CAUTION! Never store with fuel in tank for more than 30 days. Fuel deterioration can damage engine.

Warranty Information

Craftsman Pro Series Chainsaw includes a 2-year limited warranty covering defects in materials and workmanship. Warranty does not cover normal wear, misuse, improper maintenance, or use of incorrect fuel/oil. Proof of purchase required. For warranty service, contact Craftsman Customer Support at 1-888-331-4569 or visit www.craftsman.com.

Troubleshooting

Service: For repairs, use authorized service centers only.

Support: 1-888-331-4569; www.craftsman.com