Black and Decker Battery Chainsaw Manual

The Black and Decker Battery Chainsaw is a cordless, rechargeable chainsaw designed for light to medium-duty cutting tasks such as pruning, trimming, and cutting small to medium-sized branches. It features a brushless motor for increased efficiency and runtime, tool-free chain tensioning, an automatic oiler, a wrap-around handle for improved control, and a battery level indicator. Powered by a compatible Black and Decker 20V or 40V MAX lithium-ion battery. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Chainsaw body with brushless motor, Guide Bar, Saw Chain, Battery Pack, Charger, Chain Tensioning Knob, Automatic Oiler, Wrap-Around Handle, Safety Lock/Trigger.

Safety Instructions

Read all instructions before use. Wear appropriate safety gear.

1. Personal Safety: Wear safety glasses, hearing protection, gloves, non-slip footwear, and close-fitting clothing.
2. Work Area Safety: Keep work area clean, well-lit, and free of bystanders, especially children.
3. Tool Use & Care: Use the chainsaw only for its intended purpose. Do not force the tool. Keep handles dry and clean.
4. Kickback Awareness: Be aware of kickback. Do not cut with the tip of the bar. Hold saw firmly with both hands.
5. Battery & Charger: Use only Black and Decker recommended batteries and chargers. Keep away from moisture.

WARNING! Risk of serious injury. Always follow safety rules. Keep hands away from cutting area and moving chain.

Assembly & Initial Setup

Unpack all parts. Ensure you have chainsaw, battery, charger, bar, chain, and bar cover.

1. Attach Guide Bar & Chain: Place chain over bar, aligning drive links with bar groove. Fit bar onto saw body, aligning adjustment pin. Tighten bar nuts finger-tight.
2. Tension Chain: Turn tensioning knob clockwise until chain is snug against bar but can be rotated by hand. Fully tighten bar nuts.
3. Fill Oil Reservoir: Use recommended bar and chain oil. Fill via oil port until full.
4. Install Battery: Insert fully charged battery pack until it clicks into place.

CAUTION! Ensure chain is installed with cutting teeth facing forward. Always wear gloves when handling chain.

Specifications

• Power Source: Black and Decker 20V MAX or 40V MAX Lithium-Ion Battery.
• Bar Length: 10-inch or 12-inch (model dependent).
• Chain Speed: Variable speed trigger controlled.
• Weight (Tool Only): Approximately 6-8 lbs.
• Automatic Oiler: Yes, adjustable flow on some models.
• Chain Pitch/Gauge: Low-kickback, .043" or .050" gauge (check bar marking).
• Charger Input: 120V AC, 60Hz.
• Recommended Oil: High-quality bar and chain oil.
• Noise Level: Less than 90 dB(A).

Controls and Components

Main Controls: Safety Lock Button, Trigger Switch, Battery Release Button, Chain Tensioning Knob, Oil Filling Port.

Operation: Press and hold safety lock, then squeeze trigger to start. Release trigger to stop.

Maintenance Controls: Tensioning knob for chain adjustment. Oil port cap for refilling. Bar nuts for bar removal.

Battery Indicator: Press button on battery pack to show charge level via LED lights.

Operating Instructions

For cutting branches, pruning, and light limbing.

1. Pre-Operation Check: Ensure chain is properly tensioned, oil reservoir is full, battery is charged, and bar nuts are tight.
2. Starting: Place saw on stable surface. Press safety lock and squeeze trigger.
3. Cutting: Let chain reach full speed before contacting wood. Use steady, even pressure. Do not force.
4. Kickback Prevention: Hold saw firmly with both hands. Do not cut above shoulder height. Be aware of the tip.
5. Stopping: Release trigger. Wait for chain to stop completely before setting saw down.

Tip: Plan your cut and escape path. Never operate when tired or under the influence.

Chain Maintenance

Regular maintenance ensures optimal performance and safety.

1. Chain Tensioning: Check tension before each use. Chain should be snug but pull freely around bar. Adjust with tensioning knob.
2. Sharpening: Use a round file and file guide. Maintain correct filing angle (typically 30°). File all cutters evenly.
3. Lubrication: Check oil level frequently. Use only bar and chain oil. Run saw for a few seconds off the wood to distribute oil.
4. Cleaning: Remove sawdust and debris from bar grooves, oil ports, and air vents after use.
5. Chain Replacement: Replace chain when cutters are worn down, damaged, or cannot be sharpened effectively.

WARNING! Always disconnect battery before performing any maintenance. A loose or dull chain is dangerous.

Battery Care & Charging

Use only Black and Decker chargers (model specific).

1. Charging: Insert battery into charger. Charger LED will indicate status (flashing=charging, solid=complete).
2. Storage: Store battery at room temperature. For long storage, charge to about 50% capacity.
3. Disposal: Do not dispose of in fire or household trash. Recycle at an authorized service center.

CAUTION! Do not charge a damaged or wet battery. Do not expose battery to fire or excessive heat.

Storage

Clean saw thoroughly. Empty oil reservoir if storing for extended periods. Install bar cover.

Store in a dry, secure place, out of reach of children. Hang by rear handle or lay flat.

CAUTION! Always remove battery before storing. Store battery separately in a cool, dry place.

Warranty Information

Black and Decker tools are warranted against defects in material and workmanship. Typical warranty period is 2 years for the tool and 1 year for the battery. Proof of purchase is required. This warranty does not cover damage from misuse, lack of maintenance, or normal wear. For service, visit an authorized service center or contact Black and Decker Customer Service at 1-800-544-6986 or www.blackanddecker.com.

Troubleshooting

Service: For repairs not covered in this manual, contact Black and Decker Customer Service: 1-800-544-6986.