Baumr AG Chainsaw Workshop Manual
The Baumr AG Chainsaw is a professional-grade power tool designed for cutting, pruning, and felling trees. This manual covers essential safety procedures, technical specifications, maintenance guidelines, troubleshooting, and repair instructions. Below are key sections for safe operation, features, assembly, maintenance, troubleshooting, and parts identification.
Safety Instructions
Critical safety warnings to prevent injury during operation and maintenance.
| Hazard | Precaution |
|---|
| Kickback | Always hold chainsaw firmly with both hands; use low-kickback chain; avoid tip contact. |
| Rotating chain | Wear cut-resistant gloves, safety goggles, and hearing protection. |
| Fuel handling | Refuel in well-ventilated area with engine off and cool; use approved fuel containers. |
| Electrical safety | For electric models, use grounded outlet; keep cord away from cutting area. |
| Working environment | Clear work area of obstacles; maintain secure footing; do not operate in wet conditions. |
| Maintenance safety | Disconnect spark plug (gas) or unplug (electric) before servicing. |
Features and Specifications
Key components: Engine, guide bar, cutting chain, chain brake, throttle trigger, oiler system.
- Engine Type: 2-stroke gasoline engine (or electric motor for specific models).
- Displacement: Varies by model (e.g., 45cc, 52cc).
- Power Output: Typically 2.5-3.5 HP.
- Guide Bar Length: Available in 16", 18", 20" options.
- Chain Pitch/Gauge: Common: 0.325" pitch, 0.050" gauge.
- Fuel Capacity: Approx. 500ml tank.
- Oil Capacity: Approx. 300ml automatic oiler reservoir.
- Weight: 5.5-7.5 kg (without bar and chain).
- Ignition System: Electronic ignition (CDI).
- Safety Features: Chain brake, throttle lockout, anti-vibration handles.
Assembly and First Use
Unpack and inspect contents. Assemble before first operation.
- Attach guide bar and chain: Place bar on mounting studs, loop chain around sprocket and bar groove, adjust tension.
- Fill fuel tank: Mix gasoline with 2-stroke oil at 50:1 ratio (check manual for specific ratio).
- Fill chain oil tank: Use recommended bar and chain oil.
- Check chain tension: Chain should snap back when pulled from bar; adjust tensioning screw if needed.
- Start engine: Place on flat surface, engage chain brake, set choke, pull starter cord firmly.
WARNING! Never start chainsaw unless bar and chain are properly installed. Keep bystanders away.
Operation Guidelines
Proper cutting techniques for efficient and safe operation.
- Starting: Engage chain brake, set choke, pull starter until engine fires, then disengage choke.
- Cutting: Use full throttle when cutting; let chain do the work; avoid forcing the saw.
- Kickback prevention: Hold saw firmly; cut with lower part of bar; be aware of tip contact.
- Refueling: Stop engine and allow to cool before refueling; clean area around fuel cap.
- Storage: Empty fuel tank for long-term storage; run engine dry; clean saw thoroughly.
CAUTION! Always operate with both hands; never cut above shoulder height.
Maintenance Schedule
Regular maintenance ensures optimal performance and longevity.
| Interval | Task |
|---|
| Before each use | Check chain tension, sharpness, and lubrication; inspect for loose parts. |
| Every 10 hours | Clean air filter; check spark plug; clean cooling fins. |
| Every 25 hours | Replace fuel filter; clean spark arrestor screen; check bar wear. |
| Every 50 hours | Clean carburetor; replace spark plug; inspect clutch and sprocket. |
| Seasonally | Replace chain; inspect anti-vibration mounts; check all safety features. |
Chain and Bar Care
Proper chain maintenance is critical for cutting performance and safety.
- Sharpening: Use round file matching chain pitch; maintain correct filing angle (typically 30°).
- Tension adjustment: Loosen bar nuts, adjust tension screw, tighten nuts while lifting bar tip.
- Lubrication: Ensure oiler is working; check oil flow by pointing bar at light surface while running.
- Bar maintenance: Clean bar groove regularly; flip bar periodically for even wear.
- Chain replacement: Replace when cutters are worn below 0.5mm or damaged.
Tip: Keep chain sharp – a dull chain increases kickback risk and reduces efficiency.
Engine Maintenance
2-stroke engine care for reliable performance.
- Air Filter: Clean with soapy water, dry completely before reinstalling.
- Spark Plug: Clean electrode with wire brush; gap to 0.6-0.7mm; replace if worn.
- Fuel System: Use fresh fuel mix; clean fuel filter; drain carburetor for storage.
- Cooling System: Keep cooling fins clean; ensure air intake not blocked.
- Carburetor Adjustment: Factory preset; only adjust if necessary (L: low speed, H: high speed, T: idle).
WARNING! Never adjust carburetor beyond factory settings without proper training.
Troubleshooting Common Issues
| Symptom | Possible Cause | Corrective Action |
|---|
| Engine won't start | Old fuel, clogged filter, faulty spark plug | Use fresh fuel mix; clean/replace filter; check spark plug. |
| Engine starts then stalls | Carburetor adjustment, air leak | Check fuel lines; adjust carburetor (L screw); inspect gaskets. |
| Poor cutting performance | Dull chain, improper tension, worn bar | Sharpen chain; adjust tension; replace bar if worn. |
| Chain not oiling | Empty oil tank, clogged oiler, wrong oil | Fill tank; clean oil passages; use correct bar oil. |
| Excessive vibration | Loose parts, worn anti-vibration mounts | Tighten all fasteners; replace mounts if damaged. |
| Chain keeps coming off | Worn bar, improper tension, damaged drive sprocket | Replace bar; adjust tension; inspect sprocket. |
Parts Diagram and List
Reference diagram for identifying replacement parts.
- Engine Assembly: Cylinder, piston, crankshaft, carburetor, ignition coil.
- Cutting Assembly: Guide bar, cutting chain, drive sprocket, clutch.
- Control Assembly: Throttle trigger, throttle lockout, chain brake handle.
- Fuel/Oil System: Fuel tank, oil tank, oil pump, fuel filter.
- External Parts: Handles, anti-vibration mounts, starter assembly, muffler.
Note: Use genuine Baumr AG replacement parts for optimal performance and safety.
Warranty Information
Baumr AG provides limited warranty coverage for defects in materials and workmanship.
- Warranty Period: 2 years from date of purchase for residential use.
- Commercial Use: 90 days warranty for professional/commercial applications.
- Coverage: Parts and labor for manufacturing defects; does not cover wear items (chain, bar, spark plug) or damage from misuse.
- Claim Process: Contact authorized service center with proof of purchase.
- Exclusions: Damage from improper maintenance, accidents, or unauthorized modifications.
Technical Support
For assistance with operation, maintenance, or repairs.
- Website: www.baumr-ag.com
- Customer Service: 1-800-555-CHAIN (2424)
- Email Support: [email protected]
- Service Centers: Locate authorized centers via website dealer locator.
- Manual Updates: Check website for latest version of this manual.
Emergency: For immediate safety concerns, stop using chainsaw and contact support.
Baumr AG Chainsaw Workshop Manual © - All Rights Reserved 2025