ALDI Electric Chainsaw Manual

The ALDI Electric Chainsaw is a corded power tool designed for light to medium-duty cutting tasks such as pruning, limbing, and cutting firewood. It features a powerful electric motor, automatic chain oiling, safety chain brake, low-kickback chain, tool-free chain tensioning, and ergonomic handles. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Electric motor, guide bar, cutting chain, chain brake lever, oil tank, tensioning knob, front and rear handles.

Safety Instructions

Read all instructions before use. Wear appropriate PPE.

1. Personal Protective Equipment: Always wear safety glasses, hearing protection, gloves, sturdy boots, and close-fitting clothing.
2. Work Area Safety: Keep bystanders and pets at least 15 feet away. Ensure stable footing.
3. Electrical Safety: Use a grounded outlet. Keep cord away from cutting area and sharp objects.
4. Kickback Awareness: Hold saw firmly with both hands. Do not cut with tip of bar.

WARNING! Failure to follow safety instructions can result in serious injury or death. Never operate while tired or under the influence.

Assembly & Setup

Unpack and inspect all parts. Assemble on a clean, flat surface.

1. Attach Guide Bar & Chain: Place chain over bar with cutting edges facing forward. Fit bar onto saw body and tighten mounting nuts.
2. Adjust Chain Tension: Turn tensioning knob until chain fits snugly against bar but can be pulled by hand. Re-check after a few minutes of operation.
3. Fill Oil Tank: Use only recommended bar and chain oil. Fill to level indicated in window.
4. Power Cord: Ensure cord is undamaged. Plug into a 120V, 15A grounded outlet.

CAUTION! Ensure chain is correctly installed with cutting teeth facing forward. Improper installation can cause damage or injury.

Specifications

• Motor Type: Brushed electric, air-cooled.
• Power Input: 120V AC, 60Hz, 13-15 Amps.
• Guide Bar Length: 14 inches (35 cm) or 16 inches (40 cm).
• Chain Pitch/Gauge: Typically 3/8" LP, .050".
• Oil Tank Capacity: Approximately 6-8 oz (180-240 ml).
• Weight: Approx. 10-12 lbs (4.5-5.5 kg).
• Sound Pressure Level: < 100 dB(A).
• Vibration Level: < 2.5 m/s².
• Cord Length: 6 ft (1.8 m) standard; use heavy-duty extension cord if needed.

Controls and Components

Main Controls: On/Off trigger switch with safety lock, chain brake lever, oil pump control.

Front Handle: Contains trigger and safety lock. Rear Handle: Main grip with power cord entry. Chain Brake Lever: Located forward of front handle; push forward to engage brake. Tensioning Knob: Located on side for chain adjustment. Oil Filler Cap: On top or side of saw body.

Operation: Depress safety lock, then squeeze trigger to start chain. Release trigger to stop. Engage chain brake manually by pushing lever forward, or it may activate automatically on kickback.

Operation Guide

Basic cutting techniques for safe and effective use.

1. Starting Cut: Hold saw firmly. Let chain reach full speed before contacting wood.
2. Limbing: Cut branches from bottom side of fallen tree. Watch for spring-back.
3. Bucking (cutting logs): Support log off ground. Cut from top down. Avoid contact with dirt.
4. Pruning: Make undercut first, then top cut to prevent bark tearing.
5. Kickback Prevention: Always grip with thumbs wrapped around handles. Do not cut above shoulder height.

Tip: Allow the saw to do the work; do not force it. Keep chain sharp and properly tensioned.

Chain Maintenance

Regular maintenance ensures optimal performance and safety.

1. Sharpening: Use a round file and file guide. Maintain correct filing angle (typically 30°). File all cutters to equal length.
2. Tensioning: Chain should be snug but pull freely. Re-tension when chain sags or after sharpening.
3. Oiling: Check oil level before each use. Ensure oil port on bar is clear. Use only bar and chain oil.
4. Inspection: Regularly check for loose nuts, worn sprocket, damaged bar rails, and cracked chain links.

WARNING! Always disconnect power before performing any maintenance. Wear heavy gloves when handling chain.

Cleaning & Storage

Unplug and allow to cool before cleaning. Wipe exterior with dry cloth. Clean bar groove and oil ports.

Storage: Empty oil tank or turn saw on its side to prevent leaks. Store in a dry, locked place out of reach of children. Cover bar and chain to prevent rust.

CAUTION! Do not use water or solvents to clean motor housing. Never store with fuel (if applicable) in tank.

Regulatory Information

This product complies with relevant safety standards. Contains electrical components that must be recycled or disposed of according to local regulations. Not for commercial or rental use. For support, contact ALDI customer service or visit the website provided in your purchase documentation.

Troubleshooting

Service: For electrical or mechanical issues not resolved above, contact authorized service center. Do not attempt to repair motor or switch yourself.